Disposable Negative Pressure Wound Therapy Dressing Kits Size 10*7cm Including Medical Accessories Foam Joints Clip Tube

Product Introduction

1. Medical sponge: 20*15*1.2CM, 1 piece, excellent biocompatibility, right tissue; Good mechanical properties, elastic, soft, porous; Good control and absorption of wound exudate, prevent bacterial invasion and inhibit bacteria; Excellent water permeability and air permeability, which can ensure the uniform distribution of negative pressure on the wound surface, is an ideal material for trauma negative pressure treatment; Stimulate the growth of granulation tissue, protect new tissue, accelerate wound healing, stop bleeding and analgesia.

2. Transparent breathable adhesive adhesive adhesive film: 20X30CM, 2 stickers; 8X6CM, 3 STICKERS. Suitable for closure of large and small wounds. One-way high breathability, even in summer, it can ensure that the sweat of the skin is drained outside the membrane and ensure that the skin breathes normally. Gases, liquids and microorganisms outside the membrane cannot enter the membrane.

3. Round porous suction tube (inside the sponge), 3 tubes, this drainage tube is mainly a drainage tube into the sponge, and it is also a conventional drainage tube. This tube is divided into silicone tube and PVC pipe. The two pipelines have good clinical feedback and are mostly silicone tubes, which have high cost, good hardness and flexibility, and will not cause insufficient drainage due to negative pressure.

4. Suction connection drainage pipe 1 .8M, 1 strip. **Professional drainage tube, soft and elastic, unique rib groove porous flat structure, good drainage effect, patient comfort, good medical care.

5. Y-shaped connector 4*4*4, 1pcs; 4*4*6, 1pcs. The main role is the link between the drainage tubes. In particular, it plays a key role in linking large wounds with multiple sponges.

6. Stopper clamp: 3 pcs. Functions such as closing the drainage channel when replacing the drainage bottle during manual rinsing to prevent infection of the wound.

specification: (Length: 5 ~ 60cm) *( width :5 ~ 45cm) *( thickness: 0.6 ~ 4.0cm) (straight tube type, suction cup type)
Main performance indexes:

4.1 Medical foam
4.1.1 PVA foam: Honeycombed, with good three-dimensional structure and space, good permeability and water permeability, strong resilience and good biocompatibility. Physical properties: shrink and harden when the product is dry. Therefore, compared with PU foam, PVA foam is more suitable for wounds with more acute secretions with high negative pressure drainage.
4.1.2 PU foam: Composed of numerous filaments, the three-dimensional network is better in three-dimensional structure and space than PVA foam, and the density is only 1/3--1/5 of PVA foam. More breathable and permeable, excellent biocompatibility. Compared with PVA foam, PU foam is more suitable for the negative pressure sealing treatment of wounds with less dryness of various secretions and chronic refractory wounds.
4.2 porous suction tube
Silica gel material, cloth into the foam to enhance the drainage effect, strong compression resistance, according to the width and length of the foam to determine the number of porous suction tube and tube arrangement mode.
4.3 Porous flushing tube
Silica gel material, cloth into the foam to play the role of washing the wound surface, according to the width and length of the foam to determine the number and mode of porous suction tube.
4.4 Non-perforated connection tube
PVC or silica gel material, one end is connected with the flush tube installed in the foam through the corresponding specification of the joint, and the other end is connected with the guide tube through the corresponding specification of the joint.
4.5 Transparent breathable adhesive membrane
Pasting is an important material for wound closure, and the pasting process is also a key step. If wound closure and leakage directly affect the therapeutic effect of negative pressure sealing and drainage. According to different types and specifications of protecting and creating materials, different types and specifications of laminating membrane can be configured. See instructions for details.
4.6 Suction connection tube
4.6.1 Universal suction connection tube: both ends of the connection tube are 6-7mm interfaces, which can be connected with 6-7mm universal joints.
4.6.2 Special suction connection tube: one end can be connected with the negative pressure bottle of intelligent wound negative pressure comprehensive treatment instrument produced by our company, and the other end can be connected with the universal joint with a diameter of 6-7mm.
4.7 Trapezoidal
4.7.1 4×6 Trapezoidal joint: 4mm joint at one end connected to suction connection tube on foam, the other end of the 6mm joint is connected to the suction connection tube of the negative pressure bottle.
4.7.2 4×4 Trapezoidal joint: It is used to connect the same interface 4mm suction connection tube at both ends, and it is often used to extend the thin suction connection tube with large wound surface.

Straight tube foam sealing method:
In addition to good drainage, the drainage of deep tissues and deep body cavities requires straight-tube foam. PVA foam and PU foam have a straight tube type, and the sealing and drainage methods are the same.
In the mesenteric method, a single tube is generally pasted and sealed. When there are two or more tubes, it is more convenient and effective to use face-to-face pasting.
According to the wound area, size and shape, design the foam cutting, the drainage direction of the porous drainage tube or the suction cup joint, and the adhesive film sealing scheme.
As shown in the picture on the right: Cut the membrane to a width of 8--10cm, fold the centrifugal paper outward, then tear off the centrifugal paper, stick the folded edge of the folded membrane to the lower edge of the wound, place it on the wound foam, and paste the porous suction connection tube on folded film.
Apply an appropriately sized and collapsible membrane using a face-to-face paste and seal the entire wound.
8.6 Suction cup foam sealing method:
PU foam suction cup type and PVA foam suction cup type are different in structure and sealing method.
8.6.1 PU foam suction cup sealing method:
After the foam is cut, determine where the suction cup fittings will be placed on the foam and where the porous irrigation tube will enter the foam. Use a sterile scalpel to pierce the foam at an angle of 30-45 degrees, then touch the wound with sterile forceps, introduce the porous irrigation tube into the foam, and fix the porous irrigation tube in the foam by puncturing to play a certain role . Then, use two large suction cup membranes to seal the entire wound from the suction cup to the left or up.

Design foam cutting,
The perforated irrigation tube was inserted into the sponge wound at an angle of 30-45 degrees to the sponge suction surface for intermittent fixation. If the wound has sinus tracts and deep cavities, a sponge can be incised along the perforated irrigation tube for negative pressure therapy.

With the suction cup as the center, the entire wound surface is sealed with a special film made of PU sponge suction cup.After connecting with negative pressure, the wound was checked to have no air leakage, and the wound pipeline was cleaned unobstructed under negative pressure.

8.6.2 PVA foam suction cup sealing method:
After cutting the foam, place it on the wound surface and seal it with PVA suction cup special membrane. First, let the flush tube interface on the suction cup go through the corresponding hole of the membrane, and then let the suction tube interface go through successively. Let the membrane stick close to the root of the flush tube and the suction tube, and then peel off the core paper from the upper and lower membrane of the suction cup and paste the fixed suction cup and foam respectively. The special adhesive membrane is closed from the center of the suction cup to the other end of the foam, and then the adhesive membrane is set under the suction cup interface and overlapped with the above adhesive membrane by cutting two notch, and the other end of the foam is closed downward. After cutting the foam, place it on the wound surface and seal it with PVA suction cup special membrane. First, let the flush tube interface on the suction cup go through the corresponding hole of the membrane, and then let the suction tube interface go through successively.

Let the membrane stick close to the root of the flush tube and the suction tube, and then peel off the core paper from the upper and lower membrane of the suction cup and paste the fixed suction cup and foam respectively.

Tube connection:
Y-joint, trapezoidal joint are used to connect various suction tubes in the medical foam according to functions.

1.What is advantage on quality?

The company is furnished with developed equipment and technology from Germany, Belgium, and Taiwan (area).

2. What is MOQ?
30,00 pcs, It depends on requirements of products.

3. How to place a order?
Place order with salesperson
Make payment for deposit;
Sample making for confirmation before mass production;
After sample confirmed, mass production start;
Goods are finished,inform buyer to make payment for balance;
Delivery.
Production time : 30-40 days.

4. What is your term of payment?
T/T is a regular payment (30% in advance, 70% before shipping).
Paypal and Western Union are just for a sample

Shandong Chuangkang Biotechnology Co., Ltd. is an innovative company which is established in 2012. Our company is committed to research and producing PVA Dressing. We own 10, 000 square meters 100, 000-level purification GMP workshop. 1000 square meters sterile laboratory and use high-quality raw materials and advanced independent design and improvement of fully automated production equipment.

In 2004, based on the introduction of American VSD technology, we researched, developed and produced a trauma negative pressure treatment system with self intellectualperty rights, which has been registered and certified by SFDA of the StateFood and drug administration. It has also passed CE and SGS certification. This technology is the first in China and is the first to be popularized and applied in China. Now the third generation of negative pressure drainage treatment technology is fully on the market It has been used in clinic and created a newera of trauma negatve pressure treatment technology.

At present, we have been working in the First Hospital of Peking University, Qilu Hospital of Shandong University, Second Hospital of Shandong University, General Hospital of Jinan Military Region, Shandong Provincial Hospital, First Affiliated Hospital of Guangzhou Sun Yat-sen University, First Affiliated Hospital of Guangxi Medical University...

The company adheres to the business philosophy of " integrity, high quality innovation andpragmatism, making trends and being a down-to-earth person ", moving forward step by step and doing everything well in a down-to-earth manne. The products and technologies developed by the company conform to the intemational use concept, which is more convenient and efficient R & AMP: Production and sales of vanous professional medical products for the purposeof medical service and convenience Always put quality first, take meeting the requirements of customers as the work goal, and control the production process to improve our product quality and service.

Main products:

Trauma negative pressure drainage dressing

Intelligent trauma negative pressure comprehensive treatment

Negative pressure drainage protection material

Multifunctional ultrasonic debridement machine

Diabetic foot insoles